Look for parts which, through functioning, show obvious signs of deterioration. Boards requiring use of unleaded solder are printed with the lead- free mark LF indicating the solder contains no lead. Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.
Unleaded solder has the following characteristics. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
After correcting the original service problem, perform the following. Dimensions Approx. Operating temperature 0. Dimensions approx. Maximum output voltage DC 8. Mass approx. Design and specifications are subject to change without notice.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. The functions using the cassette memory require successive signals recorded on the tape. Even if the vanadium-lithium battery is not charged, it will not affect the camcorder operation. To retain the date and time, etc.
Set the time according to the local time in your country. If you do not use the camcorder for about six months, the date and time settings may be released bars may appear because the vanadium-lithium battery installed in the camcorder will have been discharged.
A smooth transition between scenes can be made even if recording is stopped and started again. Page 73 Tips for using the battery pack Notes on charging A brand-new battery pack A brand-new battery pack is not charged. Before using the battery pack, charge it completely. Recharge the battery pack whenever you like You do not have to discharge it before recharging. If you charged the battery pack fully but you did not use it for a long time, it becomes discharged. Check the picture and if the above problem persists, repeat the cleaning.
Do not Page 75 Do not use any type of solvent which may damage the finish. When you use the camcorder on a sandy beach or in a dusty place, protect it from the sand or dust. Sand or dust may cause the unit to If any difficulty should arise, unplug the unit and contact your nearest Sony dealer. Before using your camcorder abroad, check the following points. Page Trouble Check Trouble check If you run into any problem using the camcorder, use the following table to troubleshoot the problem.
Should the difficulty persist, disconnect the power source and contact your Sony dealer or local authorized Sony service facility. Camcorder Power Symptom The power is not on. Page 79 Trouble check Operation Symptom The tape does not move when a tape transport button is pressed. No sound or only a low sound is heard when playing back a tape. The new sound added to the recorded tape is not heard. The SteadyShot function does not activate. Page 80 The camcorder is not malfunctioning.
Page 82 The problem is with the AC power adaptor. Please contact your nearest Sony dealer in connection with the product with the problem. Page 86 Identifying the parts!
LINK compatible. Page Remote Commander Identifying the parts Remote Commander The buttons that have the same name on the Remote Commander as on the camcorder function identically. Page 92 To watch the demonstration You can watch a brief demonstration of pictures with special effects.
Unleaded solder has the following characteristics. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful! Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. After correcting the original service problem, perform the following. Make sure that the following accessories are supplied with your camcorder. Switching of Backup No. Shematic diagram of the VC board are not shown. Pages from to are not shown.
Printed wiring board of the VC board are not shown.
0コメント