If there are electric locks, the armrest will have to be removed by loosening the screw on the bottom. Then the door panel can be removed by loosening the 8 clips holding it to the door frame.
To remove the drivers side window and regulator, you will need to remove the door panel from the door. Then you can unbolt the regulator and window to remove them. To remove the widow its easiest to remove the outside panel. How do you remove the drivers door panel and fix the window. It fell off the track. First remove the Window Crank Handle. Then remove all of the screws you can find, 1 for the door release, 1 for the door grip, and 4 for the door panel.
Pop loose all of the lower door area, and carefullyremove the door panel. With the window all of the way down, remove the screws that hold the window in and remove the window. Revers to reinstall, being sure to locate the new window into the grooves for that. You have to remove the inside panel, where the window crank is, or would be. Remove the door panel and you will see the window regulator. There should be two or three bolts holding the door panel on, pop the window switch out and use a long flathead screwdriver to pop the panel out of the calmps securing it to the door.
I have a cadillac seville. The window won't go up. The window motor is working. I want to see if the glass window itself is off the track.
How do I remove the inside panel of the door to get to the glass window? Log in. Electric Windows. VW Jetta. Study now. See answer 1. Best Answer. Study guides. Ron 33 Veteran Member. Do a search on this. I removed mine for another reason, to take out all the foam and repair the blend doors. I think the control cables were accessible after the center radio, cd, AC Control etc were taken out. The entire dash is not extremely difficult depends on experience to remove and install, but it will take some time.
Good luck. Those control cables do not usually just come off, the plastic it is attached to just breaks. I thought I had read, in some of the thread I found, that one could just take off the side panel near the driver seat. I just dealt with this. The cable is on the driver's side, on the bottom of the heater-thing, where there is about a half-inch of clearance. On the driver's side, there is a kickpanel that has a single plastic screw; removing that might make enough space to get in there.
I pulled the console on mine that the shifter goes through ; I do not recall if it was necessary or not--the Bentley said I needed to, so I did. I also removed the lower trim on the dashboard, and the stiffener plate; I don't think any of that has to come out. Plastic Door Panel Removed. Metal Door Frame. Drill Out Speaker Rivets. Now you can pull the door panel away from the door frame and set it aside in a safe place. Power Window Motor - T Hold Panel Near Frame. Line Up Door Opener Bracket.
The power window motor is held in place to the door frame by Torx T screws. Snap In Door Opener Cable. Push In Power Plug. Route Switch Panel Plug. Double check that the door opener handle cable bracket is securely in place. Pull Out Switch Panel Plug. Hang Door Panel On Frame. Replace Torx T30 Screw. Lower the plastic door panel and hang it on the lip at the top of the metal door frame.
Line Up Pop Rivets. Line Up Rectangular Bar. Push Trim Panel In Place. Line up the plastic pop rivets on the back side of the door panel with their corresponding holes in the metal door frame. Above Storage Pocket. Attach Screw With Tape. Replace T30 Screw Clockwise. I'd recommend loosely attaching the next two screws to the top of your screwdriver with some painter's tape or duct tape so that they don't fall down in to the back side of the door panel. Line Up Plastic Cover. Replace Bottom Edge T Line up the friction fasteners on the rear of the plastic cover above the storage pocket and push it back in to place.
Replace Arm Rest Screw. Tighten T30 Clockwise. Push On Switch Panel Plug. This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only. Shipping is not available to Canada. Final shipping costs are available at checkout.
Not all parts are the perfect fit. Enter your Vehicle and we'll confirm fit, or help get you to one that will. This part will only fit a vehicle with these options. Clear vehicle X. Year Make Model. Search by Vehicle. Select your vehicle. BSS In Stock. Part 1ADLA Specify your vehicle. Loading Delivery Options. Enter your zip code.
Frequently bought together. Vehicle Fit. Part Details Operation: Power. Lifetime Warranty This item is backed by our limited lifetime warranty. Check Vehicle Fit. Product Reviews. Loading reviews. Actuator stopped working after 1 day.
Frustrating experience. I thought this Dorman lock actuator would be a good-quality product, but sadly it stopped working after 1 day! Did the job. How do you not give a good rating to a part that works.
I am coming from an angle of a guy that knows very little about how to fix anything. I always say " put a tool in my hand and my IQ drops 50 points".
But what got me looking at doing this job myself was the video put out by A1 on how to replace the Door Lock Actuator, which ultimately lead me to their website and finding that the part I got was cheaper than anywhere else I looked.
Only criticism was that maybe the part took a little longer to get but it went from East coast to West coast just after Christmas. It a good part for the price. It made my door work like new again.
0コメント